You must have javascript enabled to use treadmillsi.com !

TreadMill 1 hp 220 volt electric DC permanent magnet motor generator

12mm O

USD $129.99

Condition : New – Open box

Free Shipping

{{variant_type_name}} :
eBay
SKU: N/A This site contains affiliate links for which we may be compensated Business & Industrial / Industrial Automation & Motion Controls / Electric Motors / Permanent Magnet Motors

Notify me when the price drops

We will email you if we find a lower price on this product!

Target price (USD) $
GREAT FOR WIND TURBINE PROJECTS You are bidding on a 1 HP / 220 volt DC / 800 Watt peak electric motor. Very powerful for it's size. The 220V is the best model for low wind 12 volt and 24 volt high wind
turbines with 6 Hornet blades no longer than the stock 59" diameter max. For grid tie use only 10.8 - 30 volt model types that have a dump load built in and are rated for wind turbine use.
DIY HOME MADE WIND TURBINE
Video will open in a new window
Using the Pricetronic App? Paste link into a browser window: [isdntekvideo]
Can also be used for powering karts and bikes.
Can also be used for making Electricity (needs diode)
and changing a battery. Great for wind or hydro. Used for display - Open box model. Runs great. Never connected to power. Some dust. https://youtu.be/vsptRQFu0ks NOTE: For wind or hydro power we recommend only our 115 or 220 volt models. For go karts, mini bikes and cycles we recommend our 12, 24 and 48 volt models that correspond to your battery bank voltage. We also sell a 90 volt DC version great for DC water pumps and hydraulic motors
DC motor electric mini bike motor and project 1 hp / 3000 rpm
Video will open in a new window
Using the Pricetronic App? Paste link into a browser window: [isdntekvideo] Specifications: Motor length 3.5" diameter / 6" long. 7.5" over all length including shaft 220 volt model (800W peak) - Peak Amps is Watts divided by volts.  W ÷ V = A 12mm shaft with 1.75 pitch threads with flat slot at shaft tip. THIS IS NOT A 3/4" SHAFT! Shaft is 1.5" long with 3/4" long threaded end (12mm/1.75 pitch thread by 3/4" long) Two 5/16" extra large mounting holes on the front of the motor. 5/16" NCT mounting holes are 2.874" from center to center (74mm) 3000rpm @ 12V / continuous duty at 75% of peak wattage. Heavy 10 AWG wire to handle the amps with water resistant rubber boot. A put-up and forget design! Expect decades of dependable service life. Rain, ice and weather resistant electronics in sealed case (not for under water) Long life graphite brushes. We sell replacement brushes and bearings. Works for both CW or CCW rotations. Epoxy/Lam rotor efficiency = 94.6% (Brushed motors convert more electricity into usable horsepower) Weighs ONLY 8.5 lbs.  (Almost 100 Watts Per Pound !) Can be used as a generator, makes power when turned (Requires 100 amp blocking diode) Just Plug & Play - No expensive motor controller needed - but they are very quick and simple to replace in the field AND brushed motors convert more electricity into usable horsepower! - PRODUCT IDEAS BUILD ELECTRIC CARS / INVENT ELECTRIC BOATS / DESIGN ELECTRIC MOTORCYCLES / MINI BIKES /  GO KARTS / POWERED BICYCLES and WIND TURBINES HOW TO MAKE A TREAD MILL MOTOR WIND TURBINE Love these blades you were right, wow can they turn on, im getting up to 40 volts out of my indiana general dv pm motor,there scarey sometimes, im putting it on youtube for all to see, thanks again -uptick57

Returns Accepted for this item if it's within 30 Days

TreadMill 1 hp 220 volt electric DC permanent magnet motor generator 12mm O
| | | |
See more
Price type
IN STOCK OUT STOCK