You must have javascript enabled to use treadmillsi.com !

New MC2100 SDI 225798 Motor Controller Image15.0 17.0 17.5 1 Year

Warranty +Lube

USD $189.95

Condition : New

Free Shipping

{{variant_type_name}} :
eBay
SKU: N/A This site contains affiliate links for which we may be compensated Sporting Goods / Fitness, Running & Yoga / Cardio Equipment / Machine Parts & Accessories

Notify me when the price drops

We will email you if we find a lower price on this product!

Target price (USD) $
We will send you the latest version of this controller The new controller has been improved to use 1/5 the energy when in standby
The new design no longer requires the power transformer or heat generating power resistor.
Original controller shown for identification purposes only MC2100 SDI REVA  Same or next day priority shipping. Typical time to most US locations is two days. West Coast, Hawaii, Alaska and Puerto Rico 3 days Diagnostic Troubleshooting Guide Symptom:   Walking belt doesn't move  Turn off the power switch and remove the motor hood. Locate the red LED on the controller. It's located between the A- motor connector and the edge of the board. While observing the LED turn on the power. There should be a split second flash followed by a solidly lit LED and a beep should come from the console. If that fails to happen the controller needs to be replaced. If ok next  Next press start;  you should hear a beep and the timer should start counting. If no response the keypad may have failed. Each keypad should respond with a beep. If the motor starts for a split second then stops the controller has failed. Do not try this again as it could damage the motor.      **** If the red LED flashes 4 times pauses then flashes check the motor ****Follow our exclusive testing instructions at the end of the listing. "Battery only testing is not conclusive" The most common cause for failure is heat caused by a poorly lubricated walking belt. Includes a free 1 application of Preformant lube. Add our easy to use lube application kit for only $18.95 regularly $22.95 with controller purchase. Includes 3 lubes, application wand and storage case. No need to loosen the walking belt to lube it. We only sell parts that were purchased new from the manufacturer If you have read other listings before seeing this one be skeptical of the claims of manufacturer returns and overstock are ?? The manufacturer doesn't sell returned parts. We know this because we are an authorized seller. Also claims that the controller is new but taken out of a frame damaged treadmill are many times false. A new controller will not have scrape marks around the mounting holes. It only will from being installed during assembly. It is not necessary to mount it to test as claimed by other sellers. Each new controller is tested before we ship it so if there is a problem when it's installed we have a toll free tech support line with experienced techs. Not phone clerks and certainly not limited to E-mail We are there when you need us, when you're working on your treadmill !
****Treadmill Motor Testing**** Your motor controller may have failed due to a defect in the motor which can only be determined by doing a DC amp test. Hooking it up to a battery to see if it runs isn’t enough. The motor controller also may have failed because of a poorly lubricated or worn walking belt. It is important to properly test the motor and lubricate the walking belt before reinstalling a new or rebuilt controller. Failure to confirm the motor is within specs could result in failure of the controller. You will need 1. Digital meter with a separate jack on the front for DC amps. Clamp meters will not work for this. 2. Battery pack fully charged typically 18-20 VDC from a rechargeable power tool. Alternate voltages will work but be sure to note it in the final information needed. Test with the drive belt on 1. Set the meter function switch to the DC amp position. Typical meter will be for 10 or 20amps 2. Move the red meter lead to the DC amp jack 3. Disconnect motor leads from the controller and insert the red meter probe into the connector on the red lead from the motor. 4. Hook up the black lead from the motor to the negative terminal of the battery. If not sure which one is negative hook up the motor directly to the battery if it goes clockwise you have the black on the correct terminal. 5. Touch the black meter probe to the plus terminal of the battery. If you have it hooked up correctly the motor will run and the meter will read the amp draw. The motor needs to run for 10 seconds or so for a correct number. If it doesn't run check the fuse inside the meter. If all else fails give us a call for assistance Test with the drive belt off 6. This reading is the most important! Repeat the test with the drive belt off the motor. Most drive belts can be removed without loosening the motor by turning the flywheel and pressing outward on the belt until it walks itself off. Be certain the flywheel doesn’t have anything touching it during this test. 7. I need to know both amp readings, the voltage used for the test and both HP ratings off the motor label. Call or message us with the results. Professional Diagnostic Technicians Have a question? Contact us first and you will eliminate the guess workWe will give you the right answer the first time Century Treadmill Service Advisor8am-8pm Mon-Thurs8am-5pm Fri-Saturday EST For Assistance 877*627*0349

Returns Accepted for this item if it's within 30 Days

New MC2100 SDI 225798 Motor Controller Image15.0 17.0 17.5 1 Year Warranty +Lube
nautilus treadmill t916 | treadmill bearings | treadmill running accessories | merit 735t treadmill | manual treadmill for running
See more
Price type
IN STOCK OUT STOCK